FileVersion=1.1

# Default event gestation period
GEST_DEFAULT=0

# Default event expiry period is 24 hours
EXP__DEFAULT=86400

# Default event obsolescence period is 25 hours
OBS__DEFAULT=90000




# Default cause code for ISEE events
CAUS_DEFAULT=1x08000000

# Default service destination flags
SREQ_DEFAULT=0x00000007



CODE_UnknownEvent=1
SEVE_UnknownEvent=ERROR
TITL_UnknownEvent=Unknown event
DESC_UnknownEvent=WEBES cannot find details for this event in the resource files.
ACTS_UnknownEvent=Update the resource files to include entries for this event.
SREQ_UnknownEvent=0x00000000

CODE_DeviceAnalysisPerformed=10
SEVE_DeviceAnalysisPerformed=INFO
TITL_DeviceAnalysisPerformed=Device analysis test performed
DESC_DeviceAnalysisPerformed=%O_NAME% has performed a device analysis test on %S_TYPE% %S_NAME%
ACTS_DeviceAnalysisPerformed=
SREQ_DeviceAnalysisPerformed=0x00000000
GEST_DeviceAnalysisPerformed=0
EXP__DeviceAnalysisPerformed=300
OBS__DeviceAnalysisPerformed=420

CODE_DeviceAnalysisCompleted=11
SEVE_DeviceAnalysisCompleted=INFO
TITL_DeviceAnalysisCompleted=Device analysis test completed
DESC_DeviceAnalysisCompleted=%O_NAME% has completed a device analysis test on %S_TYPE% %S_NAME%
ACTS_DeviceAnalysisCompleted=
SREQ_DeviceAnalysisCompleted=0x00000000
GEST_DeviceAnalysisCompleted=0
EXP__DeviceAnalysisCompleted=300
OBS__DeviceAnalysisCompleted=420

CODE_DeviceAnalysisFaultFound=12
SEVE_DeviceAnalysisFaultFound=ERROR
TITL_DeviceAnalysisFaultFound=Fault found: %S_TYPE% %S_NAME%
DESC_DeviceAnalysisFaultFound=A Device Analysis test performed by %O_NAME% has found a fault on %S_TYPE% %S_NAME% [%S_SERIALNUM%]
ACTS_DeviceAnalysisFaultFound=See the attached support ticket for details
SREQ_DeviceAnalysisFaultFound=0x00000107
CAUS_DeviceAnalysisFaultFound=4x08000000

CODE_DeviceAnalysisWarningFound=13
SEVE_DeviceAnalysisWarningFound=WARNING
TITL_DeviceAnalysisWarningFound=Warning: %S_TYPE% %S_NAME% needs attention
DESC_DeviceAnalysisWarningFound=A Device Analysis test performed by %O_NAME% has found an issue that needs attention on %S_TYPE% %S_NAME% [%S_SERIALNUM%]. The issue may indicate that the %S_TYPE% has failed, or is about to fail.
ACTS_DeviceAnalysisWarningFound=See the attached support ticket for details
SREQ_DeviceAnalysisWarningFound=0x00000107

CODE_DeviceAnalysisPassedOK=14
SEVE_DeviceAnalysisPassedOK=INFO
TITL_DeviceAnalysisPassedOK=%S_TYPE% %S_NAME% is operating normally
DESC_DeviceAnalysisPassedOK=A Device Analysis test performed by %O_NAME% has found that %S_TYPE% %S_NAME% [%S_SERIALNUM%] is operating normally. This %S_TYPE% may have previously been reported as faulty, but any previous problem has been resolved.
ACTS_DeviceAnalysisPassedOK=This %S_TYPE% is operating normally and no action is required for this device.
GEST_DeviceAnalysisPassedOK=0
EXP__DeviceAnalysisPassedOK=300
OBS__DeviceAnalysisPassedOK=420
CAUS_DeviceAnalysisPassedOK=Fx88000000

CODE_ReplaceTapeDrive=20
SEVE_ReplaceTapeDrive=CRITICAL
TITL_ReplaceTapeDrive=Replace tape drive %S_GUID%
DESC_ReplaceTapeDrive=A Device Analysis test has determined that %S_TYPE% %S_NAME% [%S_SERIALNUM%] needs to be replaced.
ACTS_ReplaceTapeDrive=Replace %S_TYPE% %S_NAME% [%S_SERIALNUM%].
SREQ_ReplaceTapeDrive=0x00000107
CAUS_ReplaceTapeDrive=8x08000000

CODE_CleanTapeDrive=30
SEVE_CleanTapeDrive=WARNING
TITL_CleanTapeDrive=Clean drive %S_GUID%
DESC_CleanTapeDrive=A Device Analysis test has determined that %S_TYPE% %S_NAME% [%S_SERIALNUM%] needs to be cleaned.
ACTS_CleanTapeDrive=Clean tape drive %S_TYPE% %S_NAME% [%S_SERIALNUM%] with an unexpired cleaning tape.

CODE_ReplaceMedia=40
SEVE_ReplaceMedia=WARNING
TITL_ReplaceMedia=Replace data cartridge
DESC_ReplaceMedia=A Device Analysis test has determined that a data cartridge used in %S_TYPE% %S_NAME% [%S_SERIALNUM%] is worn or damaged, and must be replaced.
ACTS_ReplaceMedia=Identify the faulty data cartridge(s) and replace them.

CODE_OverTemperatureWarning=50
SEVE_OverTemperatureWarning=WARNING
TITL_OverTemperatureWarning=Drive is operating too hot
DESC_OverTemperatureWarning=A Device Analysis test has determined that %S_TYPE% %S_NAME% [%S_SERIALNUM%] is overheating, and this is causing problems when reading from tape, or writing to tape.
ACTS_OverTemperatureWarning=Check that the airflow through the drive is adequate, then run the LTO Cooling Check test.

CODE_OverTemperatureError=51
SEVE_OverTemperatureError=ERROR
TITL_OverTemperatureError=Drive is operating too hot
DESC_OverTemperatureError=A Device Analysis test has determined that %S_TYPE% %S_NAME% [%S_SERIALNUM%] is overheating, and this is causing problems when reading from tape, or writing to tape.
ACTS_OverTemperatureError=Verify that the airflow through the drive has been checked and that the LTO Cooling Check test has been run. If both of these actions have been performed then replace %S_TYPE% %S_NAME% [%S_SERIALNUM%].
SREQ_OverTemperatureError=0x00000107
CAUS_OverTemperatureError=4x08000000

CODE_ValidateDriveFirmware=60
SEVE_ValidateDriveFirmware=WARNING
TITL_ValidateDriveFirmware=Validate drive firmware
DESC_ValidateDriveFirmware=A Device Analysis test has determined that %S_TYPE% %S_NAME% [%S_SERIALNUM%] is encountering problems that are likely to be resolved by upgrading the %S_TYPE% with the latest firmware from HP. Automatic firmware validation is not enabled.
ACTS_ValidateDriveFirmware=Verify that the firmware installed in %S_TYPE% %S_NAME% [%S_SERIALNUM%] is the latest recommended by HP. This is best achieved by running the latest version of Library & Tape Tools (available from www.hp.com) on a server that has access to the drive, and for which FTP access to hp.com is enabled.

CODE_PowerCycleDrive=70
SEVE_PowerCycleDrive=WARNING
TITL_PowerCycleDrive=Power cycle drive
DESC_PowerCycleDrive=A Device Analysis test has determined that %S_TYPE% %S_NAME% [%S_SERIALNUM%] is encountering problems that are likely to be resolved by power cycling the %S_TYPE%.
ACTS_PowerCycleDrive=Power cycle %S_TYPE% %S_NAME% [%S_SERIALNUM%].

