IBM Netfinity 5500 5500 M10 and 5500 M20 Diagnostics Flash Update KQY1 1 58 Version 3.05 -[KQY140A-3.05]- IBM Netfinity 5500-[8660]-IBM Netfinity 5500 M10-[8661]-IBM Netfinity 5500 M20-[8662]- Windows NT 4.0 SP6 Windows 2000 KQY140A IBM Netfinity 5500 5500 M10 and 5500 M20 Diagnostics Flash Update 1.0 24p1944w 24p1944w.exe . This update is packaged as a self-extracting Package for the web (PFW). To unpack, this update requires that your TEMP environment variable be set to a path with read/write access. You must be logged in as an administrator. All IBM 2 Worldwide 20001002000000.000000-240 V3.05 - Fixed a bug where running "Normal Tests" or "Quick Tests" remotely would cause the remote connection to be dropped V3.04 - Added support for a new flash chip V3.03 - Fixed a bug where unpredictable results occur when running the PCI latch diagnostic when a slot is populated V3.02 - Added a USB Mouse diagnostic - Added the BIOS Timer test back into the Systemboard test category. This had been removed in version 3.01 due to a bug. - Fixed a bug where running the Tech Support Form utility with a pre-formatted diskette in drive a: would hang the system - Fixed a performance degredation running the memory quick tests with cache ON - Fixed a bug where a USB keyboard was not usable after running the cache test - Fixed a bug where a hang could occur when running the PCI latch diagnostic with a populated slot V3.01 - The "Date rollback problem" and "Cache test hang with MOST" are fixed. - Real-time logging to a printer, device PRN, works now. - Fixed a problem in which the VRM LED for the alternate processor would be lit when running the Alternate Processor test on a single processor sytem. The VRM is no longer lit in this case. - On-line documentation has been cleaned up V3.00 The first version of the Netfinity 5500 diagnostics which is only being released for the Model 20. - Added SCSI Tape Drive diagnostic - Added External Loopback and FIFO Buffers tests to Serial Ports diagnostic - Added support for testing a single Ethernet Fault Tolerant 10/100 adapter (part Number 08L3341) - Added support for testing of ServeRAID III adapters The following known issues exist with version 3.00: - Date rollback problem: After running the cache test if the diagnostics are kept open without rebooting across midnight, a problem may occur in which the date does not roll forward and the time is corrupted. You should check the date and time after running diagnostics under these circumstances to make sure that the date and time are correct. - Cache test hang with MOST: The cache test may hang when run from a MOST terminal through the service processor serial port. V2.01 - Test progress status is now updated on remote terminals - Fixed problem in which, when running diagnostics around midnight, the date would not roll over to the next day properly leaving the system date one day old - Fixed problem in which Internal PHY wrap tests would erroneously fail if run with an Ethernet wrap plug - Fixed problem that when running Quick Tests remotely the remote connection would be dropped. It is now OK to run Quick Tests from a remote terminal. - CD-ROM test can now be aborted more reliably by the user when pressing ESC - On-line documentation has been cleaned up V2.00 - Major feature enhancements include addition of an ECC test for system memory, tests for serveRAID adapters, enhanced cache test, removed prompt for Ethernet wrap test so test can be looped without user intervention, removed customization of serial and parallel port I/O settings and only allow USB test when no USB devices are attached. V1.02 - Changes in LED and Hot-Swap PCI Tests: Modified to work with current and all previous BIOS versions V1.00 - Initial Release 2 24p1944w.exe -s -a -s not supported not supported